Ghost 2 Immobiliser Reviews


The ghost 2 immobiliser is an innovative anti-theft device that makes use of advanced technology to prevent car theft. This discreet device is undetectable by thieves and only starts your engine after a PIN number or app is entered.

It connects to your vehicle's CAN data network and is weatherproof. It also has an option for service or valet that allows you to temporarily start your car when it's in the garage for cleaning or servicing.

Easy to install

The Ghost immobiliser protects your car from theft of keys or hacking, as well as cloning. cost of ghost immobiliser uses a unique PIN code system that is integrated into the car's ECU which makes it extremely difficult for thieves to detect or alter. It's not visible and does not use sensors or special keys. It is also a lot cheaper than replacing an ECU or installing an entirely new key fob. It also could lower your monthly insurance premiums.

Follow the directions of the manufacturer when installing follow the manufacturer's instructions when installing a Ghost 2 vehicle immobiliser. This will ensure the device is working correctly and efficiently. Test the system following installation by entering the PIN number and then starting the car. Regular testing will allow you to spot any issues early.

Before beginning the installation, double-check the position of the CAN H and CAN L wires. They are vital to powering the immobiliser, therefore it is essential to ensure that they are connected correctly. It is also recommended to label the wires to make it easier to identify them during the installation process. Once you've identified the locations of these wires and connected them to a continuous 12V power source and the grounding point. Be sure to use a fuse tap if required to shield the connections from damage or short circuits.

After connecting the wires, tidy up the wiring with cable ties to prevent potential alteration. You can also cover the connections with insulation tape or heat-shrink tubing. This will protect them from electrical shorts and increase the life span of the device. It's a great idea to test your Ghost 2 immobiliser once the wiring is secure.

The Ghost 2 immobiliser offers a service mode for situations in which you may have to sell your vehicle like when it is being repaired or valet parked. This will disable the PIN sequence for a short period of time. Press the brake pedal and hold the accelerator for a period of time equal to the first digit in the emergency code. The system will then enter service mode, which is confirmed by flashing the indicator signal 5 times.

Easy to change PIN codes

It is simple to safeguard your vehicle from theft by installing an immobiliser ghost 2. It is concealed within the vehicle and can be accessed with a special code. The device communicates with the vehicle ECU using its data bus. It does not rely on radio frequency signals, as aftermarket alarm systems or traditional Thatcham immobilisers do. This makes it difficult for thieves to detect the click of an immobiliser relay, or to add new keys. The control unit is hidden in the wiring harness or dashboard, and cannot be physically altered to reset the system.

The ghost 2 immobiliser connects to the vehicle's CAN Data network. It uses buttons on the steering, door panels and centre console, to create a programmable sequence of up to twenty button presses that must be entered to start the engine - just as a PIN. This unique system is reprogrammable and doesn't require cutting wires during installation. You can even set your vehicle in Valet or Service mode to allow it to be started for a short time when you give it to a mechanic for work.

The application can also be used to disable your PIN code in the event that you've lost your keys, or change it. This feature is particularly useful in the event that you have offered your car to someone else for valet parking or servicing since it prevents them from starting your car and driving it away without consent. It's also unnoticeable to professional thieves because it does not make use of radio frequencies or circuits.

Another great feature of the ghost 2 immobiliser is its capability to prevent thefts of relays. Relay theft is one of the most popular methods of car theft. Criminals can hack your car's diagnostic ports then alter the signal sent by the car's ECU to convince it that an authentic car key is present. The immobiliser of the traditional model can be manipulated in this manner, but with the ghost 2 immobiliser the signal is blocked by the immobiliser prior to it gets to the ECU.

Simple to use app

Ghost 2 is an immobiliser that is revolutionary. It protects your vehicle from key-cloning. It connects to the CAN data network of your vehicle and requires the use of a PIN number to start the engine. It also stops thieves from using signal spoofing and device spoofing, which are both common techniques employed to steal vehicles.

The system is simple to use and works like an ordinary auto alarm. Installing the system allows you to create a unique 20-digit pin code that must be entered before you start the vehicle. This will stop the vehicle from being stolen even if your keys get removed. You can turn off the system by downloading an app on your smartphone.

Unlike other systems it is completely silent and does not emit radio frequency signals. It is a discreet weatherproof device that can be mounted anywhere inside your car. It can be concealed under the dashboard, steering wheel or door panels. It communicates through the CAN data loop with your ECU and is not affected at all by diagnostic tools used by thieves to identify security systems. It is also not affected by jamming devices that alter codes.

It is a hidden installation that does not require any cutting of wires or modifications to the car and can be employed as an anti-theft device for all vehicles. Its technology is proven to be effective and in compliance with TASSA standards. The Ghost is a great option for classic or sports automobiles. It can also be used as a method to protect vehicles rental on apps such as Turo.

The Autowatch Ghost 2 represents the next generation of vehicle immobilisers. The system is inaccessible to thieves and blocks the vehicle from starting unless they have your PIN or are authorized by the app. It doesn't emit radio frequencies or any other signals that scanners detect. The installation process is simple and quick. The app is easy to navigate and offers a user-friendly interface which allows for easy install and use. It also has a GPS tracker that can help police find the vehicle and locate it.

Simple to reset

A ghost 2 immobiliser is a great way to protect your vehicle from theft. It is integrated into your vehicle's ECU, creating a barrier that thieves cannot breach without the correct pin. The device is also TASSA-verified that means it's acknowledged by insurance companies. It's a great tool to prevent car theft and can save you money in the end.

Contrary to traditional alarms/immobilisers which require cutting of circuits and circuit cutting, the Ghost system is directly connected to the vehicle's CAN network. It works by using your existing buttons on the dashboard and steering wheel. You can set up a unique PIN sequence that is up to 20 presses long. This PIN must be entered before your engine can start as it would be a credit card. The Ghost system is undetectable to thieves and has no indicators that make it obvious that it is there, which makes it the most reliable aftermarket CAN bus immobiliser that is on the market today.

The Ghost system also has a benefit: it does not transmit radio frequency signals. This means it cannot be detected by thieves or snatched up. This stops key attacks that replicate and relay attacks as well as the common method of hacking into the computer system of a car using its CAN bus searching for signals. The Ghost system is designed in a way that it can be hidden within your vehicle. There aren't any LEDs or other signals to show its presence.

The system has the option of a Transport Mode which disables the Ghost System. This is helpful in situations where you may require a temporary deactivation of Ghost such as when you are transporting or servicing your vehicle. However, this mode is not as effective as Service Mode, as it does not deactivate the system when your vehicle speeds over 31 mph for fifteen minutes.

You will need the emergency code from your installer to reset your Ghost 2 immobiliser. It is typically hidden under a scratch-off area on the card that was supplied with your installation. This emergency code should be secured and stored in a secure place, such as a wallet at home.