Ghost 2 Immobiliser Reviews

The Ghost 2 immobiliser makes use of the latest technology to ward off car theft. This hidden device is not detected by thieves and only starts your engine when a PIN code or app is entered.

It connects to your vehicle's CAN data network and is weatherproof. It also has the service/valet mode that allows you to start your car temporarily when it's in the garage for servicing or cleaning.

Easy to install

The Ghost immobiliser is a cutting-edge security device that protects your vehicle from cloning, hacking, and key theft. It is an PIN code system that is integrated into your vehicle's electronic control unit, making it hard for thieves to identify. It is not visible and does not require any sensors or special keys. It's also cheaper than replacing an ECU, or installing a key fob. It can even lower the cost of insurance.

Follow the directions of the manufacturer when installing a Ghost 2 vehicle immobiliser. This will ensure that the device is working correctly and efficiently. Test the system after installation by entering the PIN and then starting the vehicle. Regular testing will allow you to identify any issues before they become worse.

Before you begin the installation, make sure you check the position of the CAN H and L wires. They are essential for powering the immobiliser, therefore it is vital that they are connected correctly. Labeling the wires will make it easier to find them during installation. Once you have identified the location of these wires and connected them to a constant 12V power source and an earthing point. Use a fuse tap to shield the connections against short-circuits or damage.

After connecting the wires, tidy the wires with cable ties to avoid interference. You can also cover the connections using insulation tape or heat-shrink tubing. This will shield them from electrical shorts, and will increase the lifespan of the device. It is a good idea to test your Ghost 2 immobiliser once the wiring is secured.

In the event that you have to surrender your vehicle, for instance for valet parking or servicing, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal and hold the accelerator down for a number of times equal to the first digit in the emergency code. The system will enter service mode. This is confirmed by flashing 5 times the indicator signal.

Change PIN codes with ease

It is simple to safeguard your vehicle from theft by installing the ghost 2 immobiliser. It is installed discreetly within the vehicle, and is only accessible by a special code. The device connects directly to the vehicle ECU through its data bus, and does not use radio frequency signals like traditional Thatcham immobilisers, or aftermarket alarm systems. This makes it difficult for thieves to discern the click of an immobiliser relay, or to add new key fobs. The control unit is concealed within the wiring harness or dashboard, and is not physically accessible to reset the system.

The ghost 2 immobiliser connects to your vehicle's CAN Data network and uses existing buttons on the steering wheel, door panels and centre console to create a customisable sequence of up to 20 button presses which must be entered prior to the engine starts as it would with a PIN code. This unique next generation system does not require any wire cutting upon installation and is fully reprogrammable at anytime. You can even start your vehicle in Service or Valet mode when you give the vehicle to a mechanic who will perform work.

The application can also be used to disable your PIN code in the event that you've lost your keys, or change it. This feature is particularly useful if you have given your car to a third party for valet parking or servicing since it prevents them from starting your vehicle and taking away without your permission. It is also undetectable by professional thieves since it doesn't use circuit cuts or radio frequencies.

The ability of the immobiliser stop relay thefts is a excellent feature. Relay theft is among the most popular methods of car theft. Criminals gain access to the diagnostic ports of your car, then alter the signal sent by the car's ECU to fool it into thinking that an authentic car key is present. The immobiliser of the traditional model is able to be bypassed this manner, but with the ghost 2 immobiliser, the signal is blocked by the immobiliser prior to it gets to the ECU.

Easy to use app

Ghost 2 is an immobiliser that is revolutionary. It shields your vehicle from key-cloning. It is activated by connecting to your vehicle's CAN data network and asking you to enter a pin code before it can start the engine. It also deters thieves from using signal spoofing or device spoofing, which are both common tactics to steal vehicles.

The system is simple to use and functions similar to a standard car alarm. Installing the system will allow you to create a unique 20-digit pin code that needs to be entered before starting the vehicle. This will prevent the vehicle from being stolen even when you lose your keys. If you wish to disable the system it is possible to do this by using an app on your smartphone.

In contrast to other systems that are silent, the ghost is quiet and does not emit radio frequency signals. It is a weatherproof and discreet device that can be positioned anywhere inside your vehicle. It can be easily hidden under the dash, the steering wheel, or door panels. It communicates with your ECU over the CAN data circuit and is not affected by diagnostic tools that some thieves use to find security systems. It is also not affected by jamming devices that alter codes.

It is a covert system that can be used to stop the theft of all vehicles. Its technology has been proven be effective and in compliance with TASSA standards. The Ghost is a good choice for classic, sports, and prestige automobiles. ghost immobilisers can be used as a method to protect vehicles hired on websites like Turo.

The Autowatch Ghost 2 represents the next generation of auto immobilisers. This system is invisible to thieves, and blocks them starting your vehicle without your PIN, or unless they are authorized by the app. It also doesn't emit any radio frequencies or other signals that could be detected by scanners. The installation process is simple and quick. The app is user-friendly with a simple interface and simple navigation. It also comes with an GPS tracker to assist police locate and locate the vehicle.

Simple to reset

Ghost 2 immobilisers are a great way to protect your vehicle from theft. It is integrated into your vehicle's ECU creating a wall that thieves cannot break through without the proper pin. It's also TASSA certified that means it's recognized by insurance companies. It is a powerful tool to prevent car theft and will save you money in the end.

The Ghost system, unlike traditional alarm/immobilisers which require cutting circuits, is directly connected to the vehicle's CAN data network. It operates by pressing the buttons on your dashboard as well as the steering wheel. You can create a unique PIN that is up 20 presses long. This PIN is required to be entered before the engine can start like the credit card's PIN. The Ghost system is invisible to thieves, and there are no LEDs to signal its presence. This makes it the most reliable aftermarket CAN-bus system available today.


The Ghost system has another benefit: it does not transmit radio frequency signals. This means it cannot be scanned by thieves or intercepted. This prevents cloned keys and relay attacks, as well as the more usual method of hacking into a car's CAN bus system by looking for signals from its alarm or immobiliser. The Ghost system is designed in a way that it can be hidden inside your vehicle. There aren't any LEDs, or other signals to indicate its presence.

The system also comes with a Transport Mode that disables the Ghost system which is useful in situations in which you have to temporarily disable it, like during transportation or maintenance. However this mode isn't as effective as Service Mode, as it does not disable the system if your vehicle is traveling over 31 mph for 15 minutes.

You will require the emergency number from your installer to reset your Ghost 2 immobiliser. The code is typically hidden beneath the scratch-off portion of the card that came with the installation. This emergency code should be secured and stored in a secure location, such as a wallet at home.