How to Install a Ghost Immobiliser

Ghost immobilisers protect your vehicle from key cloning and hacking. It works by preventing the vehicle's engine from starting until it is activated using a PIN code that can be up to 20 characters in length.

This extra layer of protection is not detectable by thieves who may not be expecting it. Certain systems come with an app which allows the owner to deactivate their immobiliser if they forget their PIN or utilize the service/valet mode.

Connecting the vehicle's CAN Bus to the vehicle's

The Ghost 2 Immobiliser, a cutting edge security system, is able to be integrated directly into the ECU of your vehicle. It provides a discreet security barrier against thieves. It is highly efficient and user-friendly and can be a valuable addition to your vehicle's security arsenal. However, just like any other anti-theft device, it's not impervious to failure and requires regular maintenance to ensure proper operation. Fortunately, this guide will aid you in getting the most out of your Ghost 2 Immobiliser.

CAN (Controller Area Network) is a reliable serial networking system that lets microcontrollers communicate with each over short distances. A central control unit is not required. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It has many advantages including low cost and easy use.

In modern vehicles In modern cars, the CAN protocol is used to communicate with a variety of systems, including the engine management system (EMS), transmission controller, steering module air conditioning controls, and more. It also transmits sensor data like speed sensors and inputs to control various features of the vehicle. The CAN bus is used to monitor these diverse components, and it can stop a vehicle from starting if they are in an unsafe state.

Although the CAN bus can be used for a variety of reasons, it's essential to understand how it works and how it's secured. It is possible to add new features to vehicles using CAN bus, but it is important to protect it against hackers and other threats. The best way to accomplish this is to install firewalls and monitoring your CAN bus through software.

Ghost2's control unit is hidden in the dashboard of the car or in the wiring harness, preventing a thief from physically tampering it. It is impossible to reset a PIN or an emergency code without access to the vehicle.

ghost car immobiliser The Keylab Links to an external site. can turn on Transport Mode If you need to surrender your vehicle for valet parking, service or any other reason. This feature disables both the keyfob as well as the ignition functions of the Ghost immobiliser. It will only reactivate when the vehicle has reached 31 mph for a time of 15 minutes.

Making an PIN code

The Ghost immobiliser guards your vehicle from thieves. The latest technology utilizes the PIN code to disable the engine and prevent it from running without the correct code or a valid fob/mobile device. The system's sleek design is unnoticeable and offers unrivaled protection against theft. The system is TASSA-certified and can save you significant amounts on your car insurance.

During installation when you install the Ghost system goes into the learning mode to record the sequence of buttons that are pressed to create your unique pin code. Once the pin code is created and the installer has completed its work, it will guide you through the steps to activate the system. Once activated, the Ghost system disables the motor that starts your vehicle until you enter a valid PIN or switch the vehicle into transport mode. This makes it very difficult for thieves to duplicate or hack your vehicle's starting system.

It is simple to install a Ghost immobiliser, however, you must follow the precise instructions in the user's manual to ensure proper performance. Hand tools are essential in making the perfect connections, and a multimeter can help you verify the electrical parameters. Insulation tape and heat shrink tubing can shield the wire from damage and cable ties are essential for keeping everything tidy and secure. Also, be certain to test the system regularly to identify any potential issues and mistakes.

It is important to check the system one final time before turning on the ignition. The Ghost immobiliser will re-arm itself after a period of 3 to 30 seconds, based on the car's model. The system also comes with a Service/Valet mode that lets you temporarily disable the system for servicing or valet parking.

Ideally, the immobiliser should be hidden beneath the dashboard or on the steering wheel. It is recommended to use a small piece of duct tape or paint to mark the CAN H and CAN L wires to ensure that you easily identify them when you are testing. The CAN H and L wires must also be connected to an electrical source that delivers a constant 12V. It is also important to check the connections again after testing, since misidentifying these wires could cause the system to malfunction.

Invoking the system

A ghost immobiliser prevents your vehicle from starting unless you press a set of buttons inside the car typically the steering wheel, door panel, or central console. The sequence is set by the user and is able to be changed as needed. Once the system is activated it is not able to be disabled by thieves, making it a good choice for anyone who wants to secure their vehicle from theft.

The device is not designed to be detected by modern diagnostic tools and code-grabbing techniques. It also doesn't send radio signals which makes it difficult for thieves to identify the device.

If the device is identified, it will stop the engine from running and sound an alarm that is loud enough to scare away the thief. The device can be used to track the location of a car which can help police recover the vehicle in case it is taken.


If you are interested in a ghost-immobiliser call the experts at Car Specalist Customs to get an estimate and discuss your options. We are fully trained to install a ghost immobiliser on your vehicle and will ensure it is hidden in a difficult-to-access area. We can also install additional security measures, like a kill switch or wheel lock, to keep your vehicle safe from theft.

Disarming the system

It is essential to know how to deactivate a Ghost immobiliser if it is installed on your car. It can be used in the event that you lose your keys or the battery in your car fails. The system utilizes a unique PIN code that only you know, so the immobiliser will not start your vehicle unless you enter this code. The most efficient method of entering the code is to press a series of buttons on your dashboard or the steering wheel. This is a simpler method than using the key fob, and it also keeps anyone from copying your remote.

In contrast to some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to operate. Its most notable feature is that it shuts off the engine without affecting vehicle functions. This makes it difficult for thieves to use signal boosters or to clone keys for cars. It does not emit radio frequency, so thieves are unable to detect it.

The Ghost system has a Transport Mode which allows you to temporarily disable security for situations like transportation or service. This feature is ideal if you are lending your vehicle out to someone else, without sharing your PIN code or if your vehicle needs to be protected while you drive it. Press the service button five times over 2 seconds to activate the Transport Mode. The Ghost system will confirm activation via 5 signal signals.

Save the emergency code in your vehicle in a safe place. If you ever find yourself locked out of your car, you can call the technician or company who installed the system, and they'll provide you with the code. If you are unable to get in touch with them, you can call an authorized dealer. However, this may involve verification procedures, and you may be charged for additional fees.

This system isn't just convenient, but it can also safeguard your vehicle from theft and reduce the cost of insurance. Many insurance companies offer reduced premiums or financial incentives to install this anti-theft system.