How to Install a Ghost Immobiliser

A ghost immobiliser is a hidden security system that protects your vehicle from key cloning and hacking. It stops the engine from running until a PIN number is entered. This can be as long as 20 characters.

It is undetectable by thieves and they are unlikely to be expecting this extra layer of security. Certain systems also come with an application that lets owners disarm the immobiliser in case they forget their PIN code or to use the service/valet mode.

Connecting to the vehicle's CAN bus

The Ghost 2 Immobiliser is a cutting-edge security system, is able to be integrated directly into the ECU of your vehicle. It offers a discrete barrier against thieves. It is extremely efficient and user-friendly. This makes it an excellent addition to your vehicle's security arsenal. Like all anti-theft devices, it's not foolproof and requires regular maintenance to function effectively. This guide will help you get the most of your Ghost 2 immobiliser.

CAN (Controller Area Network) is a reliable serial network that allows microcontrollers to communicate with one another across short distances without the necessity of central control units. It is designed to multiplex electrical wiring inside vehicles to reduce copper usage and comes with a variety of advantages, including low costs and ease of use.

The CAN protocol is utilized in a majority of modern automobiles to connect with the engine management system, transmission controller, steering control module, air conditioning controls, and many more. It also transmits sensor data including speed sensors and inputs to control the various functions of the vehicle. The CAN bus can be used to monitor the status of these different components and can prevent the vehicle from starting if it's in a dangerous condition.

While the CAN bus can be utilized for a variety of reasons, it's essential to know how it functions and how it's secured. Using CAN bus can be a great way to enhance the features of your vehicle, but it's essential to safeguard it from hackers and other threats. Installing a firewall, and monitoring your CAN bus with software is the best method to accomplish this.

Ghost2's control device is hidden in the dashboard or wiring harness, preventing a thief from physically tampering it. It is impossible to reset a PIN or an emergency code without access to the car.

You can activate Transport Mode If you need to surrender your vehicle for valet parking, service or for any other reason. This option disables the Ghost immobiliser's keyfob and ignition functions, and will only come back on when the car reaches 31 mph for a period of 15 minutes.


Making PIN codes

The Ghost immobiliser is a robust security device that shields your vehicle from theft. The patented technology makes use of a PIN to disable the vehicle's engine and prevent it from starting if you don't have the correct code, or an authorized fob/mobile. Its discrete design ensures the system is not noticed and offers unparalleled protection against theft. The system is TASSA certified and can save you significant amounts on your car insurance.

During the installation, Ghost enters a "learning mode" to record the sequence of buttons that are pressed to create your unique pin codes. Once the pin code has been created, the installer will then guide you through the steps to activate the system. Once activated the Ghost system disables the motor that starts your vehicle unless you enter a valid pin or switch the vehicle into transport mode. This makes it very difficult for thieves to clone or hack into your vehicle's start system.

Installing an Ghost immobiliser is easy, but it is important to follow the precise instructions in the user guide to ensure proper operation. Multimeters and hand tools can be used to verify electrical values. Insulation tape and heat shrink tubing may shield the wire from damage Cable tie-ups are crucial to keep everything neat and secure. Also, be certain to test the system frequently to spot any problems and potential errors.

It is important to test the system one last time before turning on the ignition. Ghost immobilisers will re-arm themselves after 3 to 30 seconds, dependent on the model of your car. The system also comes with an option for Service/Valet that allows you to temporarily remove the system for servicing your vehicle or valet parking.

Idealy, the immobiliser will be hidden beneath the dashboard or behind the steering wheel. Use a small amount of duct tape or paint over the wires of the CAN H and CAN L to make them easier to find when testing. In addition the CAN H and CAN L wires should be connected to a power source that has continuous 12V. It is also important to check the connections following testing, since misidentifying these wires can cause the system to malfunction.

ghost immobiliser cost must be activated

A ghost immobiliser stops the car from starting unless you press a number of buttons in the vehicle, usually on the steering wheel or door panel, or the central console. The sequence is determined by the user and can be altered as needed. Once activated, the system cannot be turned off. This is a fantastic option for anyone who wants to secure their vehicle against theft.

The system is designed not to be detected by modern diagnostic and code-grabbing technologies. It does not emit radio frequencies either which makes it more difficult for thieves detect.

If the device is located it will stop the engine from starting. It will also sound an alarm to scare the thief away. The device can be used to monitor the location of a car which can aid in the search for the vehicle if it has been stolen.

Contact Car Specalist Customs for a quote or to discuss your options if you're interested in an immobiliser that is ghost-like. We are fully qualified to install a ghost immobiliser on your vehicle and will make sure it is concealed in a difficult-to-access area. We can also install other security measures, like a kill switch and wheel lock, to keep your vehicle safe from thieves.

Disarming the system

If you have a Ghost immobiliser that is fitted to your vehicle, it's vital to know how to disable it. This will help you in the event that you lock your keys in the car or if your battery dies. The system is based on a unique PIN code that only you know, which means the immobiliser will not be able to start your car without entering this code. Pressing a combination button on the steering wheel or dashboard is the simplest method of entering your code. This is a much easier method than using the key fob, and it also keeps anyone from copying your remote.

Ghost2 isn't intrusive unlike other immobilisers from the aftermarket which require cutting wires for installation. It also connects to the CAN bus system of your vehicle in order to function. Its most distinctive feature is that it shuts off the engine without affecting normal vehicle functions. This makes it very difficult for thieves to use signal boosters or to clone keys for cars. It does not emit radio frequencies, which means thieves cannot detect it.

The Ghost system has a Transport Mode that lets you temporarily disable security in situations like transportation or service. This feature is useful if you are lending your vehicle out to someone else, without sharing your PIN code or if your vehicle needs to be kept secure even while you drive it. To activate Transport Mode you need to press the service button 5 times in a matter of 2 seconds. The Ghost system will confirm activation using 5 signal indicators.

Save the emergency code in your vehicle in a safe place. If you ever get locked out of your car, you can call the technician or company who installed the system and they'll give you the code. If you cannot reach them You can always try contacting an authorized dealer but this would require verification procedures and could incur additional charges.

Aside from the convenience of this system, you can also rely on it to protect your vehicle from theft and reduce insurance costs. Numerous insurance companies offer reduced rates or financial incentives to install this anti-theft system.