Ghost 2 Immobiliser Reviews

The ghost 2 immobiliser is a cutting-edge anti-theft system that uses advanced technology to stop car theft. This hidden device is not detected by thieves and only starts your engine when an app or PIN code is entered.

It's weatherproof and connects to the CAN data network of your vehicle. It also has the service/valet mode that allows you to start your car for a short period when it's in the garage for cleaning or servicing.

Easy to install

The Ghost immobiliser shields your car from theft of keys, cloning and hacking. It is a unique PIN code system that is incorporated into the car's ECU which makes it extremely difficult for thieves to detect or alter. In contrast to traditional immobilisers, it does not require any specific keys or sensors. It is completely hidden from view with no LEDs or signals to signal its presence. It is also a lot cheaper than replacing an ECU or installing a new key fob and can reduce the cost of your monthly insurance.

When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's instructions carefully. This will ensure that the device operates properly and efficiently. Test the system after installation by entering the PIN number and then starting the vehicle. Regular testing will allow you to identify any problems early.

Before starting the installation, make sure you check the location of the CAN H and L wires. They are essential for powering the immobiliser so it is vital that they are connected correctly. It is also recommended to label the wires to make it easier to identify them when installing the device. Once you have identified the wires, connect them to a 12V power supply and a grounding source. Use the fuse tap to safeguard the connections from short-circuits or damage.

After connecting the wires, neaten the wires with cable ties to avoid interference. You can also cover the connections with insulation tape or heat-shrink tubing. This will protect the device from electrical shorts, and prolong its life. Once the wiring is secure, it's a good idea test the Ghost 2 immobiliser.

In ghost immobiliser where you have to surrender your vehicle, such as for servicing or valet parking for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. To activate this feature, press the brake pedal while pressing the accelerator for a number of times equal to the first digit of the emergency code. The system will enter service mode. This is confirmed by flashing five times the indicator signal.

Easy to change PIN codes

It is easy to protect your vehicle from theft by installing a ghost 2 immobiliser. It is concealed within the vehicle, and is accessible only through a specific code. The device connects directly to the vehicle ECU through its data bus, and does not use radio frequency signals as do traditional Thatcham immobilisers or aftermarket alarm systems. This makes it difficult for thieves to discern the click of a conventional immobiliser relay or add new key fobs. The control unit is hidden within the vehicle's wiring harness or dashboard and is not physically accessible to reset the system.

The ghost 2 immobiliser is connected to your vehicles CAN Data network and uses the buttons already present on the steering wheel, door panels and the centre console to create an individualised sequence of up 20 button presses. These must be entered before the engine starts as it would with a PIN code. This unique system can be reprogrammed and does not require wire cutting during installation. You can also put your vehicle in Service or Valet mode to allow it to be started for a short time when you give it to a mechanic to work.


The app can also be used to block your PIN code if you've lost your keys or change it. This feature is particularly useful in the event that you have offered your car to a third party to be used as a valet or service, as it stops them from starting your car and taking away without your consent. It's also unnoticeable to professional thieves as it does not use any circuit cuts or radio frequencies.

The ability of the immobiliser protect against relay thefts is another important feature. Relay theft is a common method of car theft in which criminals attack your car's diagnostic port, then modify the signal that is sent by the key to the vehicle's ECU in order to fool it into thinking that there is a valid key. The immobiliser of the traditional model can be manipulated in this manner, however with the ghost 2 immobiliser the signal is blocked by the immobiliser before it gets to the ECU.

Easy to use app

Ghost 2 is an immobiliser that is revolutionary. It shields your vehicle from key-cloning. It connects to your vehicle's CAN data network and requiring you to enter a PIN code before it can start the engine. It also deters thieves from using signal spoofing or device spoofing, which are both common tactics used to steal vehicles.

The system is simple to use and operates as a normal car alarm. After installing it, you can create a unique PIN code sequence that is up to 20 digits in length that must be entered prior to the vehicle's start. This will stop your vehicle from being stolen even if you lose your keys. You can disable the system with an app on your smartphone.

The ghost is quiet, and it does emit radio frequency signals. It is a weatherproof, discreet device that can be placed anywhere inside your vehicle. It can be concealed beneath the dash, steering wheel, or even the door panels. It communicates via the CAN data loop to your ECU and is not affected at all by diagnostic tools used by thieves to find security systems. It is not affected by jamming devices that disguise codes.

It is a security system that can be used to prevent theft on all vehicles. Its technology has been proven be efficient and is in line with TASSA standards. Ghost is a great solution for classic, sports and luxury cars. It can also be used to secure vehicles that are being hired out through apps such as Turo.

The Autowatch Ghost 2 represents the next generation of auto immobilisers. The system is inaccessible to thieves and prevents the vehicle from starting without a PIN or are authorized by the app. It also doesn't emit any radio frequencies or other signals that can be detected by scanners. The installation process is simple and quick. The app is easy to navigate and offers a user-friendly interface that allows for easy install and use. It also includes a GPS tracker to assist police locate and find the vehicle.

Simple to reset

It is possible to safeguard your vehicle from theft by using an immobiliser ghost 2. It works with your vehicle's ECU to create a wall that thieves cannot breach without the correct PIN. The device is also TASSA verified, which means it's recognised by insurance companies. It's an effective tool for preventing car theft, and could save you a significant amount of money in the long run.

In contrast to traditional alarms and immobilisers that require cutting circuits for circuit cutting, the Ghost system is connected directly to the vehicles CAN data network and works with the existing buttons on the dashboard and steering wheel. You can create a unique pin that is up to 20 presses in length. This PIN has to be entered before the engine can be started like the credit card PIN. Ghost is inaccessible to thieves, and there are no indicators that give away its presence, which makes it the most reliable aftermarket CAN bus immobiliser on the market today.

Another benefit of the Ghost system is that it doesn't utilize radio frequency signals, meaning it is not scanned or intercepted by thieves. This is a deterrent to key attacks that are cloned and relay attacks as and the typical method of hacking into a car's computer system using its CAN bus searching for signals. The Ghost system is designed so that it is able to be hidden inside your vehicle. There are no LEDs, or other signals to signal its presence.

The system comes with a Transport Mode which disables the Ghost System. This is helpful for situations when you require temporarily deactivating Ghost for instance, when you are transporting or servicing your vehicle. However this mode isn't as efficient as Service Mode, as it does not disable the system if your vehicle is traveling over 31 mph for fifteen minutes.

You will require the emergency code provided by your installer to reset your Ghost 2 immobiliser. The code is usually hidden under the scratch-off area of the card you received with your installation. This emergency code should be kept secure and kept in a safe place like a wallet at home.