How to Install a Ghost Immobiliser

Ghost immobilisers are hidden security system that protects your car from hacking and key cloning. It stops the engine from starting until a PIN code has been entered. It can be as long as 20 characters.

This additional layer of security is not detectable by thieves who might not be expecting it. Some systems also have an application that allows owners to disable the immobiliser if they forget their PIN code or to use a service/valet mode.

Connecting the vehicle's CAN Bus

The Ghost 2 Immobiliser, a cutting edge security system, can be incorporated directly into the ECU of your vehicle. It provides a discreet security barrier against thieves. It is extremely efficient and user-friendly. This makes it a valuable addition to your vehicle's security arsenal. Like any anti-theft device, it's not foolproof and requires regular maintenance in order to function effectively. Fortunately, this guide will aid you in getting the most out of the Ghost 2 Immobiliser.

CAN (Controller Area Network) is a reliable serial networking that allows microcontrollers to communicate with each over short distances. Central control units is not required. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It offers many advantages, including the low cost and ease of use.

The CAN protocol is utilized in a majority of modern automobiles to connect with the engine management system, transmission controller, steering control module air conditioning controls and more. It also carries sensor information, such as speed sensors and other inputs, in order to control the car's various features. The CAN bus is able to monitor the condition of these various components and can stop the vehicle from starting when it is in an unsafe condition.

It is important to understand how the CAN bus functions and how it is secured. Using CAN bus can be an excellent way to enhance the features of your vehicle, but it's also essential to secure it from threats like hackers and other hacker. Installing a firewall, and monitoring your CAN-bus with software is the best way to do this.

Ghost2's control device is hidden inside the dashboard or wiring harness, which prevents thieves from physically tampering with it. It is impossible to reset a PIN or emergency code without access to the vehicle.

If you must give your car away to a valet parking service, maintenance, or any other reason, you can use the Transport Mode. This feature will disable both the keyfob and ignition functions of the Ghost immobiliser. It will only be activated when the vehicle has reached 31 mph for a period of 15 minutes.

How do I create a PIN code

The Ghost immobiliser guards your vehicle from thieves. The revolutionary technology utilizes a PIN to shut down the engine of the vehicle and stop it starting without the correct code or an authorized fob/mobile. Its discreet design ensures that the system is inconspicuous and offers unparalleled protection against theft. Furthermore the system is TASSA certified and can lead to significant savings on insurance premiums for cars.

During installation, Ghost enters a "learning mode" to record the sequences of buttons pressed in order to create your unique pin codes. The installer will guide you through activating the system once the pin code is created. Once activated it will Ghost system will disable your vehicle's starter motor until a valid pin code is entered or the vehicle is switched to transport mode. This makes it very difficult for thieves to clone or hack into your vehicle's start system.

It is simple to install a Ghost immobiliser, however, you must follow the precise instructions provided in the user's guide to ensure proper performance. Hand tools and multimeters can be used to check electrical values. Insulation tape, heat shrink tubing and cable ties are a good option to shield exposed wiring. Be sure to test the system regularly to identify any problems and potential mistakes.

Once the installation is complete after the installation is complete, you must make a final test of the system before turning on your vehicle's ignition. Ghost immobilisers will re-arm themselves after 3 to 30 second depending on the model of your vehicle. The system also comes with a Service/Valet mode that allows you to temporarily remove the system for servicing your vehicle or parking valet.

Ideally, the immobiliser should be concealed in a hidden location beneath the steering wheel or on the dashboard. It is recommended to use a small piece of duct tape or paint to mark the CAN H and L wires so that you can easily find the wires during testing. In addition the CAN H and L wires must be connected to a power source that has constant 12V. It is also crucial to check the connections following testing, as a mistake in identifying these wires can cause the system to malfunction.

Invoking the system

A ghost immobiliser stops the car from starting unless you press a few buttons in the vehicle, usually on the steering wheel or door panel, or the central console. The sequence can be changed by the user at any time. Once activated, the system will not be deactivated. This makes it an ideal choice for anyone who wants to secure their vehicle against theft.

The system is designed to be undetectable, meaning it cannot be detected by modern diagnostics or code-grabbing technology. It does not emit radio frequencies either, making it even more difficult for thieves to identify.

If the device is located it will stop the engine from starting. It will also sound an alarm to scare the burglar away. The device can be used to track the location of a vehicle and assist in the recovery of the vehicle in case it was stolen.

Contact Car Specalist Customs for a quote or to discuss your options if you're interested in an immobiliser that is ghost-like. We are able to install ghost immobilisers on your vehicle. thekeylab.co.uk Links to an external site. will make sure that it is hidden in a place that is difficult to reach. We can also provide other security measures, such as a wheel lock and kill switch to keep your car safe from thieves.

Disarming the System

If you own a Ghost immobiliser fitted to your vehicle, it's essential to know how to disable it. This will assist you in the event that you lock your keys inside the car or your battery goes out of. The system uses an individual PIN code that only you know, so the immobiliser will not start your vehicle unless you enter this code. Pressing a combination buttons on the dashboard or steering wheel is the easiest way to enter your code. This is much simpler than using a key fob, and keeps others from copying the remote.

Unlike some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to operate. Its most distinctive characteristic is that it disables the engine without affecting normal vehicle functions. This makes it difficult for thieves to use signal boosts or to clone keys for cars. Additionally, it doesn't emit radio frequencies, so thieves can't detect the system.


The Ghost system also comes with the Transport Mode that allows you to temporarily disable the security system in occasions like transportation or servicing. This is a great option if you want to lend your vehicle to a person who isn't sharing the PIN code or if you wish to keep your vehicle secure while driving it. Press the button five times within two seconds to enable Transport Mode. The Ghost system will confirm activation with five indication signals.

When you're done, remember to save the emergency code in a safe location outside of your vehicle. In the event that you encounter a situation where you are locked out of your vehicle, you can contact the technician or the company who installed the system, and they'll provide you with the code. If you cannot reach them then you can attempt to contact an authorized dealer, but this will involve verification procedures and could result in additional fees.

This system isn't just convenient, but it can also protect your vehicle from theft and reduce insurance costs. Many insurance companies offer lower costs or financial incentives for those who install this anti-theft system.