Ghost Immobiliser Fitting

Guard your car from key theft, cloning and hacking with the first aftermarket CAN immobiliser. The Ghost app and GPS tracking can be linked to the immobiliser, which will send you alerts when your vehicle is stolen or tampered with.

Installing a Ghost immobiliser is relatively straightforward for a skilled technician. It is essential to have the proper equipment and heat shrink tubing.


Getting Started

Ghost immobilisers are a great alternative to physical theft devices like car alarms and wheel locks. They protect your vehicle without the use of LED indicators or key fobs. They are connected directly to the ECU CAN data network and are activated only after entering a PIN. This gives a greater level of security against key hacking, ECU swapping and cloning.

As a result, installing a ghost immobiliser Birmingham is a task that must be carried out with extreme speed and accuracy. It can be a bit like walking through a minefield; one misstep could cause severe damage to the circuits of the electrical system of your vehicle. To avoid this, it's crucial that you understand the procedure for installing and prepare your vehicle appropriately.

You will need to remove interior panels from the vehicle to make room for your immobiliser. Once you've found the ideal location to hide it, secure it in place using cable ties to prevent it from being taken away or altered. Then, tidy up your wiring by making sure that loose wires are tied down and using insulation tape to cover the exposed connections. This reduces the risk of a short circuit that is not intended to happen and improve the appearance and reducing the chance of theft.

Then, locate a source of constant 12V power and a grounding location for the ghost immobiliser. Once you've identified these and tested the power wires using a multimeter, to ensure they're delivering a consistent voltage. Finally, connect the CAN H and CAN L wires from the immobiliser to the designated power source and grounding point.

It's important that you ensure that all connections are checked and check the immobiliser to look for indications of corrosion. By entering a PIN and then starting the car is a great method to test the system. This should be a regular part of your routine, because it will allow you to detect any issues that might be intermittent early. Regular testing also helps to extend the life of the device, and ensure it's functioning at its best.

Preparing your vehicle

The installation of the Ghost immobiliser is a complex task that requires tools and understanding. A wiring diagram of the vehicle is vital to identify the proper wires and making precise connections. A multimeter can help verify electrical values and ensure safety. Insulation tape and cable ties can be used to protect the connections from tampering and keep them secured. A user's guide will provide specific directions tailored to the Ghost Immobiliser model you have.

Once installed the ghost immobiliser will prevent unauthorised engine start by requiring that the owner input a unique PIN code sequence by pressing buttons on the steering wheel or on the centre console. This can be done either manually or remotely through the mobile phone app and the code can easily be modified by the vehicle's owner at anytime. The device is silent and is undetectable by thieves as it does not emit any radio frequencies.

A ghost immobiliser connects directly to the vehicle's CAN bus, which is a network that connects to all the electronic control units (ECUs). It intercepts the signals transmitted by ECUs, and blocks the engine if a false one is identified. The system is tamper-proof as well as weatherproof, with no key fobs or LED indicators to attract the attention of thieves.

It can be mounted behind the dashboard or in a hidden area, so it is not visible to thieves and doesn't interfere with the vehicle's performance. It can even be mounted in a small container, making it less likely to be found during an inspection by unscrupulous car salespeople.

Its low-profile operation and integration with the vehicle's CAN bus system make it a powerful deterrent to modern methods of car theft, like key cloning and signal relay attacks. Combining the system with other security measures will create an effective barrier that will deter even the most persistent of thieves. This is why more insurance companies are advocating or even requiring ghost immobilisers to be installed, as it can significantly reduce the cost of insurance.

Making Connections

In contrast to traditional security systems that are heard by thieves ghost immobilisers are silent and stop them from knowing that your vehicle has been turned on. They also stop high tech methods of theft, like OBD hacking. Installing them without leaving permanent marks on your vehicle is an ideal option for those who intend to sell the vehicle in the near-future.

The Autowatch Ghost 2 is a immobiliser CANbus that is among the most reliable and current solutions to prevent car theft. It disables your engine using the CAN data network and generates a unique PIN code that is difficult for criminals. It is compatible with many different vehicles, and it works with many features already installed like car alarms and steering wheel locks. have a peek at this web-site and door lock bypass.

If you decide to opt for a Ghost immobiliser, make sure to consult the wiring diagram of your specific vehicle model to determine the wires that require connecting. Make sure to double-check the location of these wires to ensure that they are in the correct location, and mark them with labels or tape to make it easier to keep on track of them. It is also necessary to locate a source of constant power (12V) and a grounding point for the system. Once you have these in place, you can start making the connections to complete the installation.

The ghost immobiliser will not allow your vehicle to start unless the pin code is entered through the buttons of the steering wheel or dashboard. This will stop ECU cloning and other methods of theft of vehicles. It can also be combined with other Thatcham approved security devices such as alarms and tyre clips to give your vehicle an even greater security level.

As the UK automotive aftermarket industry continues to grow and expand, so do the options for securing your vehicle. There are many ways for thieves to get into your car and take it, which is why it's crucial to take every precaution to ensure that it isn't stolen. Ghost immobilisers are a popular option among car owners who are accountable.

Testing the System

The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU, preventing the engine from running until a specific PIN code is entered. This makes it extremely difficult for thieves to copy your key fob to start your vehicle, and more difficult to disable the system by hacking its electronic.

Ghost Immobilisers can also be used with GPS tracking devices to help you locate your vehicle if it is stolen. This isn't an everyday feature in aftermarket security solutions however it's a great option to increase your security and give you assurance that your vehicle is always secure.

In addition to providing increased security, the Ghost-II immobiliser also provides a comfortable user experience, removing the need for additional key fobs or devices. It has a simple and intuitive PIN code entry system that integrates seamlessly into your everyday routine. It also offers options for deactivation and features that allow you to temporarily disable the immobiliser to allow valet parking or for servicing.

Prepare the necessary tools and familiarise yourself first with the wiring of your vehicle. A basic set of tools will allow you to create precise connections. A multimeter can be used to verify electrical values. Insulation tape and heat-shrink tubing are vital to protect connections from short circuits. Cable ties can be used to secure wiring. It is also essential to work in an area which is well-lit and wear protective gear when working with electrical equipment and components.

You should test the Ghost immobiliser after having completed the installation to ensure it is working properly. You should first try to start the car without entering the PIN. If this fails, you'll have to retest the system and perform a more thorough inspection of the connections.

In contrast to other security systems, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is far more effective than traditional physical deterrents like wheel clamps or steering locks. It is TASSA-approved and recognized by some insurance companies. This is a cost-effective investment that provides you with the peace of heart you deserve.