Replacing uPVC Window Handles

It is simple to change the handles on windows made of upvc. barking door handle repair is to ensure that the new handle is a good fit for the spindle cut out in the window mechanism.

If the steps listed below are followed properly the cockspur handle will be able to fit into most windows. The most important factor is the step size of the handle.

What to Look For

As time passes, uPVC handles on many windows in the UK can start to show signs of wear and tear. The handle on the window can become loose or difficult-to-operate when this happens. Anyone who is familiar working with basic hand tools can complete this relatively simple job.

The first step is to ensure that the handle is securely fixed to the frame of the window in its open position. Next, locate the screws or pins which hold the handle in place. These are typically located on the inside of the handle and are removed with a screwdriver or pliers.

When the handle is loose, gently pull it away from its hinges. It is then necessary to find a new handle of the same style and size. This can be done online or at a local DIY store, and should take around five minutes using the help of a screwdriver.

One important factor to consider when replacing a uPVC window handle is the step height. This is the distance from the bottom of the handle until it rests on the frame of the window. This is a typical measurement, and you should verify the height of the step prior to ordering a replacement handle.

There are various sizes depending on the type of handle. Inline handles for uPVC windows generally have lug centres of 31mm as well as handles with cockspur that have 43mm centres. Tilt-and turn handles are typically found on uPVC Windows. They have a specific design which allows the window be tilted for ventilation, and then turned to fully open the window.


The most common uPVC handle breakage is internal cracking rather than a breakage from the base. This makes them difficult to open, and it is therefore essential to ensure that any replacement handle you buy has the same spindle length that your current one.

Remove the old Handle

A poorly fitted or damaged window handles may cause double-glazed windows to open or close improperly and could even result in them becoming stuck. This could be due to a number of factors, including general wear and tear on the handle or corrosion. In these situations, it is important to seek replacement window handles made of upvc immediately to prevent further damage and loss of function.

One of the first things that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window. Begin by removing the screw covered with the handle when it is in a closed position. Once you have removed the screw, you are able to remove the handle. You can make the job easier by using an electric screwdriver.

Be aware that screws can be hidden under caps made of plastic. It is recommended to remove the covers with a Stanley knife. After removing the handle, you will be required to inspect the square cutout on the base to ensure that the new handle for the window lock is compatible. This is important as you'll need to measure the length of the spindle on the old handle to ensure that it matches the size of the window mechanism and handle spindle that has been cut out.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned either left or right and Cranked handles that have two screws, and Spade handles which are made of flat arms and can be used on either side of the window made of upvc. It is easy to replace the handle once you have located one that is suitable. Simply screw it into place, and make sure the spindle is inserted correctly into the lock mechanism. Once that is done the handle should be secured to the window frame and your replacement window handles made of upvc should be secure.

Take a measurement of the Spindle

If you're replacing a Upvc window handle that has fallen off, it's because the spindle that holds it in place is loose or damaged. In some instances, it can be fixed using pins or screws to secure it. In other cases it will require replacement completely. There are several types of upvc window handles. There are three types of handles: inline espagnolette tilt-and-turn, and cockspur. Each handle type is installed and replaced in a different way.

Before you purchase a new handle, it is essential to know the size of the handle that is currently in use. This will ensure that the new handle is the right size and will fit correctly within the window. All handles are measured according to industry standards, so it is easy to identify the correct size.

To measure the handle's size you must turn the window to the open position. You should then be able to see the size of the screw or pin that holds it. Then you can use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle you can purchase a replacement spindle that is exactly the same size.

When purchasing a replacement window handle, it is crucial to take into consideration the step height of the upvc window handle. The step height is the distance from the base of the handle until where it sits on the frame. Typically, this is approximately 21mm for uPVC windows and 9mm for aluminium. To ensure that the new handle will work it, you can drop something into the space to check how far it goes before it comes into contact with an obstruction.

Cockspur handles typically have different backset heights depending on the style of window they are installed in. Inline Espag handles have a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles, however have different backset heights according to the style of the window they're in. This is due to the fact that they have a spur which extends from the handle and locks onto a cockspur wedge hitting plate.

Fit the New Handle

When you've picked a new handle, carefully align it to the screw holes in the door and fix it using the screws provided. If you're also replacing the latch lever, it can be installed the same way as the main door handle. After that, attach the door trim in order to conceal the mounting screws and close off your project.

Tips: To remove the head of the metal from the wedge of wood make sure the handle is held so that its longer end is resting on the floor. Use a hammer to tap the thin end of the handle. Be careful not to damage the handle or the handle spindle.