Replacing uPVC Window Handles

The replacement of window handles made of upvc is an easy task. It is crucial to ensure that the new handle fits into the spindle cutout of the window mechanism.

If the steps below are followed correctly the cockspur handle will fit most windows. The height of the step of the handle is key.

What to Look For

Over time, uPVC handles on many windows in the UK may begin to show signs of wear and wear and tear. When this happens, the window handle can become loose or difficult to operate, which makes it essential to replace it. Anyone who is comfortable using a basic hand tool can accomplish this fairly simple job.

The first thing to do is make sure that the handle is firmly fixed to the window frame and is in a position that is open. The next step is to find the fixing pins or screws that keep the handle in the position it is in. They are typically located on the inside of the handle. They can be removed with the screwdriver and pliers.


Once the handle has become loose, gently pull it away from its hinges. Then, you'll have to find a new handle of the same size and style. This can be done online or at the local DIY store and should take around five minutes using the help of a screwdriver.

When replacing the handle on a uPVC handle It is crucial to consider the step height. This is the distance from the bottom of the handle to the point at which it is placed on the frame of the window. This is usually an average measurement, but it is crucial to determine the step height of your existing handle prior to ordering an entirely new one.

There are several sizes depending on the type of handle. Inline handles can be found for uPVC window with lug centres of 31mm while cockspur handles come with centers of lugs of 43 millimetres. Tilt-and-turn handles are commonly found on uPVC Windows. They feature a unique design that allows the window to be tilted to allow for ventilation and then turned to fully open the window.

The most frequent uPVC handle breakage is internal cracking rather than a breakage from the base. This can make them hard to open, and it is therefore crucial to ensure that any replacement handle you purchase has the same spindle length as your existing one.

Remove the Old Handle

A poorly installed or damaged window handles can cause double-glazed windows to open and close improperly and could even result in them getting stuck. This could be due to a number of factors, including general wear and tear on the metal handle or corrosion. In these instances it is crucial to find replacement handles made of upvc as soon as possible in order to prevent further damage and loss of function.

When replacing upvc windows handles, you should remove the old handles from the window. Start by removing the screw with the handle when it is in a closed position. This will reveal a screw that once removed, you can then begin to take off the handle itself. It is a good idea to use an electric screwdriver for this since it will make the job easier and faster.

Be aware that screws could be hidden in caps made of plastic. It is recommended to remove the covers using the help of a Stanley knife. After you have removed the old handle, you will have to examine the square cutout on the base to ensure that the new handle for the window lock is compatible. It is essential to measure the length of the spindle on the handle that was used and compare it to the dimensions of the window mechanism spindle cutout.

The different types of window handles made from upvc include: Espag handles, which are equipped with a central screw and can turn left or right; Cranked handles which have two screws and are found on tilt and turn upvc windows and Spade handles that have an arm that is flat and can be used on either side of the window. It is simple to replace the handle when you've found one that is suitable. Just put it in place and make sure the spindle is correctly inserted in the lock mechanism. Once this is done the handle should be secured to the window frame and the replacement window handles made of upvc must be secure.

Take a measurement of the Spindle

If you're looking to replace a upvc handle that has fallen, it's likely the spindle holding it in place is damaged or is loose. In certain situations it is possible to tighten the spindle with pins or screws. In other cases it will need to be replaced entirely. There are several kinds of window handles made of upvc. There are three kinds of handles: inline espagnolette, tilt-and-turn, and cockspur. Each type of handle is installed and replaced in a different manner.

It is important to measure the handle prior to purchasing an alternative. This will ensure that the new handle is the correct size and will fit correctly into the window. Fortunately, all handles adhere to industry standard sizing so it's relatively easy to identify the correct size.

To determine the size of your handle, first, take it out of the window by turning it to an open position. You should then be able to determine the size of the screw or pin that secures it. Make use of a ruler or tape measure to determine the length the spindle is. Once door handle repairs have determined the length of the spindle, you can buy a new spindle that is the same length.

The step height of a upvc window handle is also important to take into consideration when you are buying an alternative. The step height is the distance from the base of the handle to the point at which it rests on the frame. In general, this is around 21mm for uPVC windows and 9mm for aluminium. To be sure that the new handle will fit it, you can drop something into the space to check how far it extends before it comes into contact with an obstruction.

Cockspur handles typically have different backset heights based on the style of window they're installed in. Inline espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles have different backsets, based on the window they are in. This is due to the fact that they have a spur that extends from the handle and is locked onto a cockspur wedge hitting plate.

Fit the New Handle

If you've decided to replace the handle, carefully align it with the screw holes on the door and secure it with the supplied screws. If you're also replacing the latch lever the lever can be mounted the same way as the door handle. Then, you can attach the door trim to hide the screws for mounting.

Tips: To take the metal head from the wedge made of wood make sure the handle is held so that its wider end is resting on the floor. Use an hammer to tap the thin end of the handle. Be careful not to scratch the handle or spindle.