Upvc Door Lock Replacement

Change the lock on your uPVC door is an easy DIY task. It's less expensive than hiring a locksmith and you can shield your door from damage if your cylinder is opened without a key.

uPVC locks are found on most domestic front and back doors as well as French and patio doors. The most common lock cylinder is manufactured by Everest.

Fixing the Cylinder

The cylinder is part of the lock which accepts the key and turns it. It is fitted with tumblers that are aligned when the correct key is placed. Changing the cylinder is an easy and effective method to increase your uPVC door's security.

It is recommended to leave this job to a professional. Making the change by yourself may damage your door and cause you more issues in the long run.

A locksmith can help by removing the lock and replacing it with a brand new one. They can also provide advice on the type of cylinder that is most suitable for your door. They will also ensure the lock is fitted securely and works properly.

It is possible to need to replace your cylinder due to a variety of reasons, including following a burglary or moving house. You may also want to increase the level of security at your home or to meet the insurance requirements. A professional locksmith will be able to provide you with a variety of uPVC locks that meet your requirements.

To replace your cylinder, you'll need a screwdriver and a set of screw extractors. You can find these tools at most hardware stores and online. Start by loosening the screws that hold the door handle and face plate. The next step is to open the door to access the side of the faceplate for the lock and also the inner frame's edging. The screws can be removed and saved in a secure location.

After you have removed the faceplate, you can remove the cylinder. Insert the key into the hole and turn it right or left for about 10 degrees. This will loosen the cylinder, allowing you to take it out of the hole. Test the key to make sure that it works properly.

If the key isn't turning properly, you may need to lubricate it by using a small amount of grease or oil. The majority of hardware stores sell lubricant, and many locksmiths also carry it. This will allow you to unlock your door without much effort.

Fixing the Sticking Mechanism

The upvc door lock mechanism can become stuck or a little difficult to lock and close. In these situations, a little bit of troubleshooting may help you solve the issue without having to replace the whole mechanism. It is possible to begin by inspecting the mechanism to determine what's causing it to stick. It could be as simple as the internal hinges being unlubricated or something more serious, like a damaged gearbox.

You can also lubricate your locks at home by using household products like WD40. This will help keep them in good shape and extend their lifespan. It is also essential to use a soft-bristled brush to get rid of any debris or dirt that has accumulated inside the locks. Keep your upvc lock oiled and tightened to ensure they last longer. This will also reduce the force needed to open and shut them.

If you're experiencing a lock problem it is recommended to speak with a specialist rather than trying to fix the problem yourself. It's not worth putting yourself at risk of damaging your uPVC door or causing more problems to the locking mechanisms in the future. It's also better to pay an extra amount and have peace of mind knowing that the work is done professionally by someone who has years of experience.

If you're planning to replace the locks on a uPVC lock yourself you should follow a tutorial or watch a tutorial video to ensure you are aware of what you're doing. If you don't, you could quickly cause more damage, and possibly breaking the cylinder as well as the door handle.

Fixing the door handle that is loose

Many people alter their uPVC handles for many reasons, including to increase security or to comply with insurance requirements. It is important to ensure that the replacement handles you choose are good quality to avoid issues like the handle becoming floppy.

If the uPVC handle is loose, it's likely that the mechanism must be tightened. It's usually a simple procedure that you can complete yourself. However, if you aren't confident in DIY projects, you should employ an expert locksmith.

The first step is to unhook the handle, and then locate the screw that holds it in place. Once you've found it, tighten the screw using the help of a screwdriver. It might take a few attempts to get the screw to line up correctly, but you must be careful not to tighten it too much or cross-thread it. Once the screw has been secured, you can install the handle to check that it works correctly.

You could also replace the entire handle plate, instead of just the screw. Depending on the type of lock, you might need to use different screws for this task. Make sure that the handle is in alignment with the keyhole, and it doesn't stick or move when you turn it.

You could also grease the mechanism to make sure it's not stuck in a problematic position. If the issue persists then it's best to call an expert double-glazing repair service.

If you're replacing broken or old locks out of choice or in a situation that requires it the process can be stressful. It is therefore advisable to hire a qualified locksmith to do the job for you so that the job is completed to the highest standards and any additional issues are avoided. They can also give you advice on the best locks for your home. They can help you find an Sold Secure SS301-approved set, or 2* Kitemark.

Fixing the damaged Gearbox

If you are experiencing problems with your uPVC doors, it might be time to replace your lock. Fortunately, the issue isn't as severe as you think and can be easily fixed by locksmiths. You should be aware that replacing the entire mechanism could be expensive, so it is not something you like to tackle at home.


To start, it is essential to understand what type of door you have in order that you can purchase the right parts for an upvc door lock replacement. In order to get a replacement lock you must take a measurement of your lock to determine the manufacturer. It will make the process much simpler if you are able to refer to the original lock that was installed on your door.

You should also make sure that you have the proper tools to repair a upvc lock. These include screwdrivers and a drill. With the right tools, you will avoid damaging your door while trying to repair it. Once window lock replacement near me have the right tools, follow the directions provided by the manufacturer to install the new lock properly.

After you have the replacement, you'll be required to test it, and then make any necessary adjustments. This will ensure that the replacement is functioning properly and can be used according to the specifications. It is recommended to consult a professional if you are unsure of how to do this job correctly.

If you notice that your door handle of your upvc is sloppy or loose, it could be an indication of an issue. If you do it, the problem is most likely to be with the 'barrel' portion of your lock. If this component of the lock is loosened and you are experiencing issues with your door handle. This is where the key indent is located. To tighten your handle, locate the screw that holds the barrel of your lock in place and tighten it with the help of a screwdriver. This will make the handle more secure and resolve your problem with a loose door handle.

Although it may seem intimidating at first to remove the uPVC door in order to replace the gearbox or lock cylinder, the modular nature of these doors makes it relatively easy for most people to complete this task on their own for much less than the cost to engage a locksmith.