Upvc Door Lock Replacement

Changing the lock on your uPVC door is a simple DIY task. It's much cheaper than hiring a locksmith and you can protect your door from damage if your cylinder is opened without a key.

Most domestic doors, including French and patio doors, are equipped with uPVC locks. The most common lock cylinder is made by Everest.

Fixing the Cylinder


The cylinder is the component of the lock that accepts and turns the key. It is fitted with tumblers that align when the correct key is inserted. Changing the cylinder is an easy and efficient way to increase your uPVC door's security.

However, it is something that should be left to a professional. Attempting to change the lock by yourself could damage your door and cause you additional problems in the end.

A locksmith can assist you by removing the lock and replacing it with a new one. They can also advise you on the type of cylinder that would be most suitable for your door. They will also make sure that the lock is fitted securely and functions effectively.

There are a variety of reasons why you could want to replace your cylinder, for instance after a burglary or moving home. You may want to improve the security of your home or comply with insurance requirements. A professional locksmith can provide various uPVC locks to suit your requirements.

To replace your cylinder, you'll need a screwdriver and an assortment of screw extractors. These tools are available in many hardware stores or on the internet. Begin by loosening the screws that are holding the door handle and face plate. The next step is to open the front door to reach the inner edge of the door frame as well as the side of lock faceplate. The screws can be removed and put away in a safe place.

Once you have removed your faceplate, you are able to remove the cylinder. Inject the key into the hole and turn it to the right or left for about 10 degrees. This will loosen up the cylinder and allow you to take it out. Test the key to make sure that it is working properly.

If the key isn't turning, you might want to lubricate the key with a little bit of oil or grease. Hardware stores usually offer lubricant and many locksmiths also carry it. This will help you unlock your door without a lot of hassle.

Fixing the Mechanism that Sticks

The door lock mechanism made of upvc may become stuck or a difficult to close and lock. A little troubleshooting can help you fix the problem without having to replace the entire mechanism. Begin by examining the mechanism and determining the reason causing it not to work. It could be something that is as simple as hinges not being properly lubricated, or it could be something more serious, such as a damaged gearbox.

You can also lubricate your locks with household items such as WD40. This will help to keep the locks in good condition and can extend their lifespan. Use a soft-bristled brush to remove any dirt and debris that has accumulated within the lock. Keep your upvc lock oily and tightened to make them last longer. This can also decrease the force needed to open and close them.

It is recommended to contact a professional to fix an issue with a lock rather than try to do it yourself. It's not worth the risk of damage to your uPVC door or causing more issues with the locking mechanism in the future. replace upvc window lock paying more to have peace of mind that the work will be done professionally by someone with years of experience.

If you're planning to replace the lock of a uPVC lock on your own you should follow a manual or watch a video so that you know what you're doing. If you don't follow the guide, you could quickly cause more damage and potentially even breaking the cylinder and the door handle.

Fixing the floppy door handle

Many people choose to change their uPVC door handles for a variety of reasons, such as wanting to increase security or to meet insurance requirements. It's important to choose replacement handles of high quality to avoid issues like the handle becoming floppy.

If the uPVC handle is loosened, it's likely that the mechanism must be tightened. This is typically a simple procedure that can be completed by yourself, however if you're not sure about DIY projects, you should call in a professional locksmith to do the task for you.

First, remove the handle. Next, locate the screw that holds the handle in the correct position. Once you've found it, tighten the screw using the help of a screwdriver. It could take several attempts to align the screw correctly. Be careful not to overtighten or cross-thread. Once the screw is secure, you can re-insert the handle and check whether it's working properly.

You can also replace the entire handle plate instead of just the screw. Depending on the lock type, you may have to make use of different screws. Once you have replaced the handle, check that it is in alignment with the keyhole and it isn't slipping or moving when you turn it.

You could also grease the mechanism to ensure it isn't stuck in a bad position. If the problem persists then it's best to contact a professional double-glazing repair service.

It can be a stressful task to replace your broken or damaged locks, whether you're doing it on your own or out of necessity. It's therefore worth hiring a professional locksmith to complete the work for you to ensure that the work is done to a high standard and any additional problems are avoided. They'll be able to guide you on the best locks that suit your home. They can help you find the Sold Secure SS301-approved set or a 2* Kitemark.

Fixing the damaged Gearbox

If you're experiencing issues with your uPVC doors, it might be time to replace the lock. The good news is that the issue is usually not as severe as you think and can be easily fixed by a locksmith. However, you should know that replacing a full mechanism can be costly, so this is not something you want to try at your own home.

It is essential to be aware of the kind of door you need to get the correct parts to replace your upvc door. You'll need to know the model of your lock, and then determine the measurement to find an appropriate replacement. This process will be easier if you own the original lock that was installed on your door to refer back to.

It is also important to ensure that you have the right tools to repair a upvc lock. These include screwdrivers as well as a drill. If you use the correct tools, you can avoid damaging your door when trying to fix it. Once you have the tools, you should be sure to follow the directions given by the manufacturer to ensure you can put in your new lock properly.

Test the replacement and make any adjustments necessary after you receive it. This process will ensure that the replacement is working correctly and is able to be used according to the specifications. If you're unsure how to do this correctly, it's a good idea for you to hire a professional.

If you notice that your door handle made of pvc is sloppy or loose, it could be an indication of a problem. If so it, the issue may be to be with the 'barrel' portion of your lock. If this component of the lock is loosened, you will have problems with the door handle. This is the area where the key's indent located. To tighten the handle tighten the screw that holds your barrel lock with the help of a screwdriver. This will tighten your handle and fix the problem of a loose handle.

The modular design of uPVC doors makes it easy for most people to do it themselves and for a lot less money than hiring locksmiths.