Ghost 2 Immobiliser Reviews

The ghost 2 immobiliser is a cutting-edge anti-theft system that utilizes modern technology to ward off car theft. This discreet device is unnoticeable by thieves and only turns on the engine when a PIN or app is entered.

It connects to the CAN data network of your vehicle and is weatherproof. It features a service/valet function that lets you temporarily start your car when it is in garage.

Easy to install

The Ghost immobiliser is a cutting-edge security device that shields your vehicle from cloning, hacking, and key theft. It utilizes an PIN code system that is integrated into your vehicle's electronic control unit, making it impossible for thieves to recognize. Contrary to traditional immobilisers it doesn't require special keys or sensors and is completely hidden from view with no LED indications or signals to give away its presence. It's also cheaper than replacing an ECU, or installing a key fob. You could even lower your insurance premiums.

When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's instructions carefully. This will ensure that the device functions properly and efficiently. After the installation is completed, test the system by entering the PIN code and then starting the engine. Regular testing will allow you to identify any problems early.

Check the location of the CAN H and L wires before beginning the installation. They are vital to power the immobiliser, so it is vital that they are connected properly. It is also recommended to label the wires to make it easier to locate them when installing the device. Once you have identified the locations of these wires, connect them to a constant 12V power source as well as a grounding point. Make sure you utilize a fuse tap if required to shield the connections from short circuits or damage.

After connecting the wires, neaten the wiring using cable ties to prevent interference. It is also recommended to cover the connections with insulation tape or heat shrink tubing. This will shield the device from electrical shorts and prolong its life. It is a good idea to test your Ghost 2 immobiliser once the wiring is secure.

In the event that you have to surrender your vehicle, for instance for valet parking or servicing for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal and hold down the accelerator for a number of presses equal to the first digit of the emergency code. The system will then go into service mode, which is confirmed by flashing the indicator signal five times.

Change PIN codes easily

It is simple to secure your vehicle from theft by installing a ghost 2 immobiliser. It is concealed inside the vehicle and can be accessed using a specific code. The device communicates directly with the vehicle ECU via its data bus. It does not use radio frequency signals as do traditional Thatcham immobilisers, or aftermarket alarm systems. This makes it harder for thieves to detect the sound of an immobiliser relay, or to add new keys. The control unit is hidden within the wiring of the vehicle's dashboard, and isn't physically altered to reset the system.

The ghost 2 immobiliser connects to your vehicle's CAN Data network and utilizes the buttons already present on the steering wheel, door panels, and centre console to create an individual sequence of up to 20 button presses which must be entered prior to the engine can start - just like a PIN code. This innovative next-generation system does not require any wire cutting upon installation and is fully reprogrammable at any time. You can even set your vehicle in Service or Valet mode to allow it to be started for a short time when you give it to a mechanic to work.

The app can also be used to block your PIN code if you've lost your keys, or change it. This feature is particularly useful when you have lent your car to someone else to be used as a valet or service because it prevents them from starting your vehicle and driving it away without your permission. It is also undetectable to professional thieves since it does not make use of radio frequencies or circuits.

The capability of the immobiliser to protect against relay thefts is another great feature. Relay theft is one of the most frequent methods of car theft. The criminals hack the diagnostic ports of your car, then modify the signal sent by the car's ECU to fool it into thinking that a valid car key is present. This is the way traditional immobilisers are removed, however with an immobiliser that is ghost 2, the signal is blocked before it reaches the ECU.

Simple to use app

Ghost 2 is an immobiliser that is revolutionary. It safeguards your vehicle from key-cloning. It connects to the CAN data network of your vehicle and requires an PIN code to start the engine. It also deters thieves from using signal spoofing and device spoofing, which are both common techniques used to steal vehicles.

The system is simple to use and operates similar to a standard car alarm. Once you have installed it, you can generate a unique PIN sequence of up to 20 characters long and must be entered before the vehicle starts. This will prevent the vehicle from being taken away, even if you lose your keys. You can disable the system by downloading an app for your phone.

Contrary to other systems that are silent, the ghost is quiet and does not emit radio frequency signals. It is a quiet weatherproof device that can be placed anywhere inside your car. It can be concealed in the dashboard, behind the door panels or the steering wheel. It communicates through the CAN data loop with your ECU and is not affected at all by the diagnostic tools used by thieves to locate security systems. It is also not affected by jamming devices which spoof codes.

It is a hidden system that can be used to stop theft on all vehicles. Its technology has been proven effective, and it complies with TASSA Standards. The Ghost is a great option for classic, sports, and prestige cars. It can also be used as a way to protect vehicles being rental on apps such as Turo.

The Autowatch Ghost 2 is the next generation in car immobilisers. This system is invisible to thieves, and prevents them from starting your car without your PIN or unless they are authorized by the app. It does not emit radio frequencies or other signals that scanners can detect. The installation process is simple and quick. The app is simple to navigate and has a user-friendly interface that makes it easy to set up and use. It also includes a GPS tracker that can help police find the vehicle and locate it.

Simple to reset

It is possible to protect your vehicle from theft using an immobiliser ghost 2. It integrates with your vehicle's ECU to create a barrier that thieves are unable to break through without a valid PIN. The device is also TASSA-certified that means it's acknowledged by insurance companies. It's a great tool to deter theft of your car and will save you money in the end.


In ghost immobiliser and tracker to traditional alarms and immobilisers that require cutting circuits, the Ghost system is connected directly to the vehicle's CAN network and works with the existing buttons on the dashboard and steering wheel. You can create a unique pin that is up 20 presses in length. This PIN needs to be entered before your engine can begin as it would be a PIN on your credit card. The Ghost system is inaccessible to thieves and has no lights to indicate its presence. This makes it the most efficient aftermarket CAN-bus immobiliser available today.

The Ghost system has another advantage that it doesn't transmit radio frequency signals. This means that it is not stolen or scanned by thieves. This is a deterrent to cloned key attacks and relay attacks, as well as the common method of hacking into the computer system of a car using its CAN bus searching for signals. The Ghost system is designed so that it can be concealed inside your vehicle. There aren't any LEDs, or other signals to signal its presence.

The system also has an option for a Transport Mode that disables the Ghost system that is helpful in situations when you need to temporarily deactivate it, such as during transportation or maintenance. However this mode isn't as effective as Service Mode, as it does not disable the system if your vehicle goes over 31 mph for fifteen minutes.

To reset your ghost 2 immobiliser, you'll need the emergency code, which you can obtain from your installer. It is typically hidden beneath a scratch-off section on the card that was provided when you installed the device. It is recommended to keep the emergency code secure and keep it in a location that is secure, such as your wallet at home.