Ghost Immobiliser Installation

Ghost immobilisers stop thieves from copying your vehicle's key fob and stealing your car. The device connects to your vehicle's CAN network, and prevents the engine from starting until a pin code has been entered using buttons on your dash or the steering wheel.

Certain systems allow the owner to temporarily disable the system with an app on their mobile, for example when lending their vehicle to a third party to valet or service. Insurance companies often offer discounts for those who have ghost immobilisers.

Covering the Immobiliser Unit

A ghost immobiliser is an advanced vehicle security system that stops your car from starting until you enter a pre-set PIN code sequence. It utilizes your vehicle's existing buttons such as those on the steering wheel, dashboard and door panels to create an individual code that needs to be entered in order to start your vehicle. The device operates silently so that thieves are unable to detect its presence. It is an increasingly popular method of protecting keyless entry vehicles. The device is also becoming more popular with insurers, and can lower monthly premiums.

The most well-known method of taking a car away is through a process called'relay hacking, which is where thieves take and amplify the signal transmitted by the remote key of your car. This enables them to open and start your car. Installing a ghost ignition will protect you from this type of theft by stopping your vehicle from starting even within the reach of the fob.

It is crucial to follow the instructions provided during the installation process. This will ensure that all connections have been made correctly and that the Ghost immobiliser is working properly. Utilize hand tools that are basic to create precise connections. A multimeter is required to verify the electrical value. Insulation tape and cable ties are used to protect wiring from short circuits.


After your Ghost immobiliser has been fitted and is ready to use, however we suggest that you perform regular tests of the system by entering the PIN code, then turning on the engine of your vehicle. This will help you find any issues with your system swiftly and avoid a possible breach of your vehicle's security.

A Ghost Immobiliser is a low-cost, easy to use and effective way of protecting your vehicle from cloning, hacking and relay attacks. It is TASSA-certified and does not require a transponder or key fob. It's a popular choice for many drivers and is a great option if you are planning to sell your car in the future.

The Wires Need to be nipped up

The Ghost 2 immobiliser blends in with your vehicle's wiring and isn't visible. This makes it an effective deterrent for thieves who are unable identify or disable the system. It also has a PIN code that can be personalized by the user for extra security. Autowatch's Security Guarantee also reinforces their confidence and provides a guarantee on the effectiveness of the product.

The first step in installing an immobiliser that is ghost-like is to find the CAN L and H wires that connect to your vehicle's bus system. This requires the right tools and techniques, since incorrectly stripping or identifying the wires can cause the immobiliser to cease working. Utilizing safety gloves and flashlights will ensure you can accurately work in the dark areas where these wires are, without causing accidental damage to your vehicle's wiring. The Ghost Immobiliser user manual may provide more details to help you determine these areas.

Once you have identified the CAN L and H wires, remove one small piece to expose the copper conductors underneath. The connection can be made with high-quality connectors or solder. It is crucial to use high-quality parts as poor connections could lead to electrical shorts or malfunctions of the immobiliser in your vehicle. Recheck the connections to make sure they're solid and properly sealed.

In the end, the Ghost immobiliser has to be connected to a source of power and a grounding point. Identifying a consistent 12V source is crucial, since it will supply the immobiliser with required power. It is crucial to have a good grounding point in order to avoid power surges and protect the system from electrical faults.

After the connections have been made, it's time to test the Ghost immobiliser. You can accomplish this by pressing a series of buttons that are programmed to arm the system (these can be programmed using the buttons on your car's dashboard like those on the steering wheel, door panels and centre console). If you're concerned about your car being stolen, Autowatch's Ghost 2 immobiliser comes with Transport Mode for temporary disarming when renting your vehicle on platforms such as Turo.

Power Connection

A ghost immobiliser can prevent your vehicle from being stolen by preventing communication with the ECU. It uses relays to block the signal sent by your key fob. This makes it impossible for thieves to clone your car or hack it. It also warns you if there is any suspicious activity.

During installation, it's crucial to ensure that the power connection is insulated and secure. A bad connection could damage your vehicle's electrical wiring and require costly repairs. Therefore, you should only try a ghost immobiliser installation if you have the right tools and knowledge.

If you don't have much experience working with cars, it's best to look up online guides and installation guides. These can provide useful suggestions and information that will assist you in completing the installation with ease. It's recommended to check your work twice to ensure that all connections are secure and secure.

While the cost of an Ghost immobiliser may seem high but it's a small cost to pay for peace of mind and improved security. The device can be linked with a tracking system or alarm to notify you and authorities of any attempted tampering or theft. It is also able to stop the vehicle from being driven until a particular PIN configuration has been entered.

The Ghost immobiliser also has the advantage of being silent, so that criminals can't hear it. This is a major advantage over immobilisers that can be heard by criminals at a distance. It can be combined with a Thatcham approved tracker to keep track of your vehicle at all times. This is a huge benefit if you're worried about the security and contents of your vehicle. It can even help reduce monthly insurance costs. Get in touch with Skidz today to find out more about our Ghost immobiliser installation service and other solutions for car security.

Ground Connection

It is important to follow a few key guidelines during the installation process for safety and accuracy. First, work in a well-lit space to ensure that you clearly see. Wear the appropriate safety gear to safeguard yourself against electrical shocks. It's also a good idea to go through the user manual of the immobiliser. This will allow you to know the requirements and installation for your specific model.

After the installation has been completed It is important to test the immobiliser to ensure that it's functioning properly. As part of your routine vehicle inspection, you'll need to enter the PIN code to start the engine. This will allow you to spot any issues early and resolve them quickly.

ghost ii immobiliser The Key Lab will stop your car from being stolen. It connects to the CAN data network of your vehicle and utilizes the buttons on your dashboard or steering wheel to create a unique pin sequence. This means that thieves will have a difficult time copying the signal from the key fob in your car to start the engine. This will reduce the chance that your car or van could be stolen, which makes it an investment worth considering.

In order to install a Ghost Immobiliser it is necessary to determine the ground and power connections. Once you've identified the power and ground connections and are able to connect your Ghost Immobiliser to the wiring system of your vehicle. Make sure that the wires are properly insulated and marked to avoid an accidental disconnect or damage. Also, ensure that you reconnect the battery to restore the electrical power to your vehicle's system.

The Ghost II is a TASSA-verified immobiliser which protects against key cloning or theft. It is discrete and works quietly to prevent engine starting through the vehicle's data network CAN. It allows you to create your own PIN code sequence, which only you are able to use. This makes it impossible for thieves bypass the system. In addition the installation of Ghost II Ghost II may also lead to lower insurance costs because it proves that you're accountable for your vehicle's security.