Choosing the Right UPVC Door Handle Replacement

It's easy to replace your handles made of upvc however choosing the best handle can be a challenge. Modern double-glazed handles have spring cassettes built into the handles, but older ones don't.

If your upvc handle seems loose and floppy, there could be an issue with the internal parts of the multipoint lock. This article will cover a number of potential problems & their causes.

Handles that sag or loosen

UPVC handles are prone to wear and wear and. This is especially true in older properties. A damaged spring cassette on the door lever is the most typical cause of a floppy handle. This is typically caused by excessive force and the square spindle that holds the cassette can become displaced or the cassette can be rounded off.

It is good to know that a uPVC handrail replacement can be done in just a few minutes. The first step is to disassemble the handle unit that was previously installed by removing the fixing screws that are visible on the side of the lever plate. Once the handles have been removed you can remove the cassette from the square spindle, and replace it with the new one.

On the internet, you can select from a range of uPVC handles that come in different finishes. The finish you select will determine the durability of your handle as well as how it will be easy to clean. Finishes such as PVD, Stainless Steel or Resista are made to withstand corrosion and will last for up to 25 years.

After you have chosen the colour or style you can then select the kind of handle you want. The most commonly used types are pad and lever arrangement. Lever pads are often used to stop access from unauthorised people. They are equipped with a lever inside and a paddle outside.

The next step is to measure the dimensions of your existing handle and write them down. You will need to measure the PZ dimension which is the distance between the screw hole and the center of your lever. It is also important to know how the handle's length is and the dimensions of its keyhole. You can compare the measurements with the size matrix of the handle to find the appropriate replacement.

Broken springs

Over time, the handles of uPVC doors may become wobbly or loose and sometimes the spring cassette inside may break. These springs are used to align the handle lever in a horizontal direction. Without them your doors will not lock properly.

Modern uPVC handles have these cassettes built into the back plate. However, older uPVC doors typically include these springs in the lock mechanism. It is not something you can do yourself, but it's worth asking your locksmith to examine the issue as it could be the reason for the sliding uPVC handles.

One of the most frequent issues with uPVC door handles is that they get loose or wobbly over time. This is typically due to worn-out springs, which is a relatively simple fix. The majority of the time the reason for this is excessive use of the handle and because of that the square spindle in the handle will wear away and the springs will move out of place.

To fix this, you will need to open the door towards the handle plate and then remove all the screws. This can be accomplished using the Philips screwdriver. Once the screws are removed the handle can be removed and the plates pulled apart carefully. Then, you can remove the springs from the old ones and replace them with new springs.

This is a crucial point to remember when purchasing a new handle. This measurement is known as the PZ and it is important to make use of a calibrated measuring tape in order to get an exact reading.


After reinstalling the springs, you should be able to operate the handle without issue. However, it's always worth lubricating the internal mechanism to ensure that everything works just as it should. This will ensure that your uPVC door is as secure as is, and improve their comfort as time passes.

Handles that slide around

Handles that slide could be caused by a variety of factors. One of the most frequent causes is when the levers of the handle aren't aligned with the lock. This can happen on both uPVC doors as well as composite doors. However, it's more noticeable on older doors since they are constructed of lower quality materials that don't stand up to the elements.

This issue can be fixed by a professional, who will re-align the handles and ensure they're in line with the door lock. They will also look at the lock itself to determine if there is anything that needs fixing. In many cases, a simple modification to the springs of the handle is all it takes to fix this issue.

Switching your uPVC door handle is easy enough, but it's important to take the measurements of the handles that are in use to make sure you have the proper size replacement. You'll need to measure the distance between the two fixing screws and the dimensions of the lever as well as the key-hole position. Then, you can use this uPVC handles size guide to locate an appropriate replacement for your home.

Once you have the measurements then the next step is to remove the current uPVC handles. It's usually a straightforward procedure and requires only the use of a screwdriver. Once the screws are removed, you will need to remove the handle and then install the new handle.

Before ilford upvc door handle replacement Links to an external site. begin the work, you should ensure that the door is securely open with a door wedge to stop it from closing in the middle of your work. After you have removed the handle, you will be able to access the parts underneath the door that cause the door to move.

A handyman from Fantastic Services will be able to help if you don't want to do the job yourself or don't have the skills. They will employ sophisticated lock picking techniques to open the doors without creating damage. They will then replace the damaged handle and make sure that everything is working as it should.

Gearbox damaged

A damaged gearbox could cause the upvc handle to become stiff and lose functionality. The lock could also not be able to opened by keys. This could be extremely dangerous and should be addressed as soon as possible. If you are unable resolve the issue yourself it is crucial to call a locksmith since they have the expertise and tools to do the job right.

The first step is removing the handle from the cover plate. This can be done using a screwdriver with flat heads. After you have removed the handle, take out the middle screw which holds the barrel. After taking out the middle screw, you will be able to loosen the two screws that secure the barrel. Then you can take the barrel out of the door. You'll have to prop the door open to do this, so make sure you have someone on hand to help.

After removing the cylinder, you can replace with a brand new cylinder. Make sure the new cylinder is the exact size as the previous one. You might have an incorrectly aligned handle. This can cause a variety of problems, such as leaks and drafts.

A lot of doors made of upvc have adjustment slots that allow you to tighten or loosen the handle. They are usually on the inside of the door, near where the handle meets the cylinder. Allen wrenches can be used to tighten the slots of adjustment. Once you have made the adjustments, you can put the handle back into place and screw it in. Then, you can test the handle and make sure it is working as expected.

If the upvc door handle becomes loose or floppy when it is closed, this is usually an indication that the gearbox in the upvc has broken down or internal spring components are in the process of breaking down. This could cause the multipoint lock made of upvc to fail, leaving your door open to intruders. In this case the upvc gearbox will need to be replaced. This will cost between PS145 between PS145 and PS280 with the labor included.