Bi-Fold Door Repair

Bi-fold doors are suitable for internal or external use. They are flexible and can be tailored to meet your needs. Like other fittings and fixtures, they could be susceptible to wear and tear.

Fortunately, it's not too difficult to restore them to good shape. With some patience and basic woodworking knowledge, you can tackle a couple of easy bi-fold door repair projects.

Cracked Corners

Bifold closet doors are usually light and are susceptible to cracking near the pivot points. This is usually caused by the natural deterioration of wood. This can be easily fixed by clamping and gluing the affected wood. The procedure is fairly simple and will save you the cost of hiring a professional to complete the task for you.

Bifold doors are typically not able to close or open smoothly. This is typically caused by a misalignment in the pivot pins or guides of the bifold doors. This can be caused by an unbalanced door or loose pivot pins or guides which are simple to fix by a little effort.

It is recommended to first examine the runners and tracks for any obstructions or blockages. Sand, dirt, leaves, pet fur and anything else that could get on a running track will cause issues for a bifold door. Cleaning and lubricating the tracks regularly will keep them in good condition.

If you notice that a door is leaning when closed, it will likely require trimming. It is essential to use a circular type of saw to accomplish this as the doors aren't that thick. You should also be careful to avoid damaging or chipping the door's veneer while trimming it. Place the door on a stable table and mark a line using a pencil. Cut the door with circular saw to follow the line.


A bifold door can also cause carpeting to rub when it is opened or closed. This can cause seals to break and allow in drafts, making your home less energy-efficient. It's good news that this is a fairly simple problem to repair. You'll need to clean the seals with a non-abrasive solution such as vinegar or mild dish detergent, and then apply silicone sealant on the affected area. After the sealant has dried it will be solved. This will also prolong the life of your seals and the doors in general.

Doors that are not aligned

If your bifold doors are sticking or jamming when you attempt to open them or slide them closed, it is a sign that they are out of alignment. This could be a significant risk to your home's security. As soon as you see this problem, it is essential to take action. Delaying repairs could lead to damages that require more extensive and expensive repair work.

Fortunately the adjustment of your bifold door is relatively easy. Make sure the track is clear of obstructions and clean. It is possible to use a cloth or brush to clean up dirt or other debris that has accumulated over time. After the track is clean you can lubricate it with a silicone spray or other type of fluid to smooth the movement of doors.

Then, you'll need to adjust the pivot brackets to ensure that your doors are in the correct position. The brackets are situated at the upper and lower corners of the frame of the door and are held to the frame using screws. If your door is dragging on the floor you can raise it by loosening the screws and tightening them later. If it is pulling away from the wall you can lower it by loosening the screws, then tightening them. Continue to make small adjustments until the doors are perfectly aligned.

Also, it's important to ensure that the door frames have been secured. If the frame is moved slightly it can cause gaps between the doors, which will allow air and water to be able to enter your home. It could cause hinges to become misaligned and uneven doors. If this happens you'll require resecuring the frame.

Also, check whether the doors are aligned with the floor. You'll have to adjust the hinge bolts if not in the right position. This can be accomplished by opening and closing the doors. Then, you can use the spirit level and screwdriver until the panels are all level.

Shag Carpeting

The bi-fold doors are built to slide up and down, but they may scratch the floor or wall. This is usually caused by one or more pivot pins that aren't aligned correctly.

This issue is usually simple to fix. The pivot pin is located at the bottom of the bi-fold door. It is connected to a floor bracket. At the top, a spring-mounted retaining pin engages a sliding bracket which locks into the track. If your bifold door gets scratched on the carpet you can raise it by turning the pivot pin on the bottom counterclockwise.

Another reason you might be experiencing a shagging problem in your bi-fold doors is that the track that they slide on isn't level. This could be due to shifting, settling or even changes in the weather and could cause the bi-fold door not to close properly. If this is the case, try to adjust the track by loosening the screws holding the upper track bracket and then sliding it up or down until it is level with the bottom track bracket.

Another issue that could be affecting your bi-fold door is that the wood has cracked around one or more pivot pins. This is a problem that many doors suffer from and includes bifolds. You will need C-clamps and a small amount of carpenter's adhesive to fix this. To begin, take off the door and pry out the pivot pin using the help of a screwdriver. Spread the glue using a toothpick over the crack, clamp the door and allow it to dry for 3 to 4 hours.

You should have your bi-fold doors repaired by an expert, no matter how minor or serious the problem is. bifold door glass replacement cost will stop further damage and ensure that the door is functioning correctly. To locate a professional in your area, look at the website of your door's manufacturer for a list of installers who have attended their training in the installation of their product. Then call them to set up your bi-fold repair appointment.

Broken Slats

Louvered doors to closets let air circulate, stop mildew from developing and allow your clothes to see. They can be a great feature for a home, but the task of repairing or replacing them can be difficult.

Louver doors are composed of slats that are able to open and close to let light, rain or air into the room. They are typically made of polyurethane or wood molding and are often used in windows, doors or walls. Certain bifold doors don't have louvered slats, but those that do have louvered slats may become misaligned over time or break.

When a slat breaks you might think it's time to buy an entirely new door, but this isn't the case. Instead, you can fix the broken slat using a piece of fabric and carpenters glue.

Begin by removing the closet door from the track and placing it on the floor or a set of saw horses so that the slats face upwards. You'll want to work on the door while having it positioned in this way to avoid damaging or bending the hinges or tracks.

To remove a damaged slat from the door, place a claw-type of Hammer under each slat. Then, jerk up the slat in order to separate it. Once the slat is detached, measure the area from the point of removal to get the width and length required to make the new slat. Once you have the measurements, cut a piece of foam board or cork to the same size as the area where the broken slat has been removed.

Apply a thick line of carpenters glue to one side of the foam board. Then, place the fabric on the back of the board and smooth out wrinkles or wrinkles as you move. Place the slat carefully into the door's slot, and if necessary, secure it with nails. When the glue has dried you'll be able to rehang your bifold closet door.